1x HINGE PIN for Encore/Prohunter Black Nitride

0 Review(s) Write a Review

Your Price: $20.00

Part Number: 377

Availability: In Stock.

Quantity

Description

Brand new, limited run!

1X HINGE PIN for Encore/Prohunter in Black Nitride finish.

Ultimate weather resistant, natural lubricity and a Slightly tighter fit than a non coated pin.

If your barrel drops open easily and has any side to side movement when opened, that "play" at the hinge does not go away when the barrel is closed, and it permits the barrel to move in an inconsistent manner while the bullet is traveling through it. To reach a barrels accuracy potential, this play at the hinge area must be removed. Stop wasting ammo trying to get your barrel to shoot, just oversize the hinge pin.

The hinge pin holes in Encore barrels and frames vary much more than the holes in Contenders, so much so that in some instances the hinge pin must be at least .003" larger than "stock" in order to get the same degree of precision fit common to the Bellm Oversize Contender Hinge Pins.??Reaming for these 1x pins is virtually never necessary. At .4377" they fit most all factory and custom barrel hinge pin holes. Testing the fit of the 1x pin in each hole gives an indication as to whether the next larger pin is needed to get the optimum fit desired, that of a bank vault door opening and closing. I know, you never had the privilege, but you get the idea. It does not shake and rattle all over the place.??Use the 1x pin as a gauge pin. If it is not tight enough, consider it as a gauging tool to determine if a larger pin is called for.??Taking accurate measurements of pins and holes is common among machinists, but not in the realm most folks are familiar with. Thus, the best solution I have found to bridge this technology gap is to simply use a process of elimination by going from one size pin to the next. Anyone can tell if a pin is loose or tight, right? The Encore hinge pin system is a well proven system. "Trial and error" is working very well, and groups are tightening. That is what counts.??So, start with the 1x pin unless you have a means of accurately measuring your hinge pin holes in your barrels and frames. By the way, calipers are not accurate enough to give more than a rough idea. Trying a pin is still the best method available to most shooters.??Add a 1x pin to your cart and get started toward better shooting Encore barrels.

Test fitting the hinge pin fit is as Simple as lubricate the hinge pin, frame and barrel hole with a common cutting/tapping or heavy viscosity oil, the key is ANTI binding/bearing lube. Center the hinge pin on a given hole checking for axial play and resistance. If it is not tight enough, consider it as a gauging tool to determine if a larger pin is called for. When installing the oversized hinge pin, always install the stock hinge pin first, then tap out of the way with the oversized pin. Always remember the lube.

Taking accurate measurements of pins and holes is common among machinists, but not in the realm most folks are familiar with. Thus, the best solution I have found to bridge this technology gap is to simply use a process of elimination by going from one size pin to the next. Anyone can tell if a pin is loose or tight, right? The Encore hinge pin system is a well proven system. "Trial and error" is working very well, and groups are tightening. That is what counts.

So, start with the 1x pin unless you have a means of accurately measuring your hinge pin holes in your barrels and frames. By the way, calipers are not accurate enough to give more than a rough idea. Trying a pin is still the best method available to most shooters.

20 points will be rewarded to you when you buy this item.

HD locking bolt spring single

$2.70

always in stock

Add to Wish List

Add To Cart

Trigger Job Manual tc encore prohunter g2 trigger job manual tjm

$16.95

In Stock.

Add to Wish List

Add To Cart

6.8 SPC Encore Barrel 20 Inch CeraKote Matte Finish

$450.00

Out of Stock.

Add to Wish List

TC7660 Encore Katahdin Forend Black

$55.00

Out of Stock.

Add to Wish List

300 Blackout/300 Whisper® Encore 16.25 Inch Barrel with TSOB Scope Base and Thread Protector

~~$550.00~~ $495.00 Sale

Out of Stock. Free Shipping.

Add to Wish List

209x50 Stainless Muzzle Loader Barrel with Williams Peep and Forend

$495.00

Out of Stock.

Add to Wish List

[history_item_name]

[ITEMPRICE] ~~[ITEMPRICE] Original price~~ [ITEMSALEPRICE] Sale

Clear

1x HINGE PIN for Encore/Prohunter Black Nitride

Reward Points

Related Items

Recently Viewed Items